Rijlab · Drivetrain Simulator
Discover how it all works together
Rijlab shows what happens inside a manual-transmission car when you accelerate, brake or change gear. Explore how the engine, clutch, gearbox and wheels work together.
What can you do?
Operate the clutch, accelerator and brake, select gears and watch the drivetrain respond. The virtual driver usually handles the clutch and matches engine RPM during shifts. With Auto off, you can hold the clutch fully open yourself when selecting a gear.
Follow the moving parts, tachometer and coloured connections. Bright dots indicate transmitted mechanical power. Fainter dots indicate rotation with little or no power transfer. In neutral the engine side and wheel side can rotate independently.
Experiment for yourself
Slow simulated time, adjust engine power or use the gear icon to tune shift duration, clutch bite point and bite-zone width.
For kickdown, reach 100% accelerator, pause your drag briefly, then push farther right while still holding. One drag and hold stays at normal full throttle. Release to end kickdown.
SET stores the current speed; RES resumes it. While active, SET/RES adjust by 1 km/h. ±10 and the blue handles change the stored target without engaging CC. Dragging snaps to 5 km/h. Accelerator input overrides CC without cancelling it; release to coast back without braking. Manual braking cancels CC. Manual shifts keep CC active. CC assists the clutch without changing your settings; a manual clutch input or lock keeps priority. In manual neutral at a standstill, select first or enable Auto Gear before requesting movement. An unsuitable gear starts a three-second correction countdown.
Listen to the drivetrain
Enable sound with the red speaker beside the volume slider. Engine load, engine braking and cranking have different voices. A stalled engine produces no combustion sound, even when the wheels still turn it. Sound is independent of static view.
A simplified vehicle model
Shaft inertia, synchronizer friction, elastic engine mounts and suspension pitch drive the motion. Drag the stick through neutral and hold pressure to synchronize. Starting normally cranks for two seconds; adjust Starter duration in Settings. The windshield follows body pitch while the dashboard stays fixed. Wheel rotation and vehicle speed are simulated separately. ABS controls brake pressure using wheel-slip feedback. There is one equivalent wheel, with no steering or separate axle dynamics.
Engine recording: JoniHeinonen, CC BY 3.0 (edited).
Controls and shortcuts
| Q / A / Z | Set and lock clutch: 100%, middle of bite zone, 0% |
|---|---|
| E / D / C | Set and lock accelerator: 100%, 50%, 0% |
| W / S | Brake at 50% / 25% while held; release to stop braking |
| ↑ / ↓ | Hold for 100% accelerator / 50% brake |
| → / ← | Upshift / downshift one gear |
| Shift+Q | Toggle Clutch Auto |
| Shift+E | Toggle Shift Throttle Assistance |
| Shift+G | Toggle Gear Auto |
| 0 / N, 1–6 | Choose neutral or gear 1–6 |
| Space | Emergency braking at 100% while held, with rapid pedal application |
| P | Pause or resume the simulation |
| Enter | Press for ignition, then to start. At a standstill, press to stop a running engine and switch ignition off. While moving, hold half a second, then keep holding through the five-second countdown; release to cancel. |
| L | Cycle headlights through off, low beam and high beam |
| F | Flash high beam while held |
| K | Enable or disable kickdown availability |
| ` / ~ | Open or resize live telemetry. The ~ button is at the top right. |
| Esc | Close the telemetry console when open, or dismiss help |
| = / −, + / _ | Adjust the stored cruise target by 1 / 10 km/h; does not engage inactive CC. |
Pedal depressed
Engine speed
Shift thresholds
These thresholds govern the automatic driver. A red triangle flags conflicting settings. Open it for details or to restore both defaults. The personality sliders in Settings adjust these values; changing them here keeps a manual override.
After an upshift, RPM can fall below the downshift threshold. Auto may then shift back down and keep switching between gears. Adjust the thresholds or restore the defaults.
Select gear
Quiet view: decorative motion is off. Instruments and controls still work. Use Pause to stop the simulation as well.